Ships within 1 business day — domestic US fulfillment
Not sure which part you need? Upload a photo and we'll find it. →
Troubleshooting14 min readUpdated October 2026

Hot Spring Spa Error Codes: Full List & Fixes

A complete, model-aware reference for Hot Spring spa error codes across Flair, Highlife, Limelight, Hot Spot, and Jetsetter lines. Includes a code/cause/fix table, IQ 2020/2021 panel guidance, and direct links to the sensors, switches, and control parts that resolve each fault.

On this page

What Hot Spring Spa Error Codes Mean

Hot Spring spas run on a control pack — the sealed electronics box that manages the heater, circulation pump, and pumps — paired with a topside display or IQ 2020/2021 panel. When the pack detects a condition outside normal operating range, it shows a short alphanumeric code instead of the temperature. That code is not a random glitch. It is the pack reporting a specific sensor reading, switch state, or safety trip so you can narrow down the problem before opening a panel or calling a technician.

Codes fall into a few families: flow and pressure faults (the pack cannot confirm water is circulating), sensor faults (a temperature sensor is reading incorrectly or has failed), high-limit and overheat trips (a true or false overtemperature condition), generic electrical faults (short or open circuit on a component), and system-level states like Standby or Protection Mode. Salt-system spas add a second layer of alerts tied to water chemistry rather than the heating circuit.

Exact code text varies by control board generation. An older analog topside, an IQ 2020 panel, and the newer IQ 2021 display do not always use identical abbreviations for the same fault, and Hot Spring has changed code naming across model years. If the code on your display does not match one below exactly, treat the closest match as your starting point and confirm against your model's owner's manual, available from hotspring.com.

Where to Find Your Error Code

On spas with a simple topside display, the code appears in place of the set temperature, usually flashing. On Flair, Highlife NXT, Limelight, and other models with the IQ 2020 or IQ 2021 control panel, the code shows on the main screen, sometimes with a short description beneath it. A few things to check before you start diagnosing:

  • Flashing vs. solid: A flashing code is usually an active fault the pack is still monitoring. A code that stays solid after you've addressed the obvious cause (clean filter, correct water level) points to a failed component rather than a temporary condition.
  • Multiple codes: Some panels cycle through more than one code if several conditions are flagged at once — for example a flow fault alongside a sensor fault, since restricted flow can cause both.
  • Panel responsiveness: If the display is blank, dim, or unresponsive rather than showing a code, that points to the keypad or ribbon connection rather than a sensor or flow problem. See our keypad overlays collection if the touch panel itself has failed.

Complete List of Hot Spring Spa Error Codes

This table covers the error codes most commonly reported across Hot Spring's Flair, Highlife, Limelight, Hot Spot, and Jetsetter lines. Use it as a starting point, then jump to the detailed section below for each code family.

Code What It Means Likely Cause Quick Fix
FL1 / FLO Flow switch not detecting circulation Dirty filter, low water level, closed valve, air lock, failed flow switch Clean/replace filter, check water level, bleed air lock, test flow/pressure switch
FL2 Secondary flow fault on dual-pump systems Restricted plumbing or weak circulation pump Inspect circulation pump, check for blocked suction
SN1 Primary temperature sensor fault Sensor reading out of range or wiring fault Inspect sensor connection, replace temperature sensor
SN3 Secondary (redundant) sensor fault Mismatch between primary and secondary sensor readings Replace sensor pair as a set; check sensor wiring and connectors
HL High-limit switch tripped Water temperature exceeded the safety cutoff, often due to restricted flow Clear flow restriction, let spa cool, reset at breaker; replace heater element if it recurs
OH Overheat protection shutdown True overheating or a sensor reporting false high temperature Check filter and flow first, then test sensors; inspect control pack if sensors read normal
Er1 Generic sensor open-circuit fault Broken sensor wire or failed sensor Replace sensor
Er2 Generic sensor short-circuit fault Pinched or shorted sensor wire Inspect wiring harness, replace sensor if shorted internally
Er3 Pressure/flow switch stuck closed Switch reading flow with pump off Replace pressure switch
Er4 Pressure/flow switch stuck open Switch not reading flow with pump on Clean filter, check for air lock, replace switch if fault persists
dEr / dr Protection mode / standby triggered Pack has shut down heating to protect the system after repeated faults Power cycle at the breaker, resolve underlying fault before reset holds
Code 4 (Flair FreshWater Salt System) Low salt reading Salt level has dropped below target range Add salt per manual instructions, retest water
Code 5 (Flair FreshWater Salt System) Salt cell or sensor fault Cell fouled, miswired, or failed Inspect cell connections, replace if fault persists

FL1 / FLO - Flow Switch Errors

FL1 and FLO are the most common Hot Spring codes, and the good news is they are usually the cheapest to fix. The pack has a flow or pressure switch in the plumbing line that confirms water is moving before it allows the heater to fire. If that switch doesn't see flow, the pack shuts the heater down and throws the code rather than risk running a dry or starved heater element.

Start with the filter. A clogged filter is the single most common cause of flow codes — it restricts intake enough that the switch reads no flow even though the pump is running. Pull the filter and check it against the cleaning schedule in your owner's manual. Next check water level; if it has dropped below the skimmer line, the pump draws air instead of water. An air lock after a filter change or drain/refill can cause the same symptom and usually clears by running the pump briefly with the air relief valve open, if your model has one.

If the filter, water level, and air lock are all fine and the code persists, the flow switch itself has likely failed or is stuck in position. These are inexpensive, position-sensitive parts — see our pressure and flow switches collection for replacements, and confirm paddle or pressure-type orientation before ordering since the two are not interchangeable.

SN1 / SN3 - Sensor Faults

Hot Spring packs use two temperature sensors that cross-check each other as a safety redundancy. SN1 flags a fault on the primary sensor; SN3 flags a mismatch or fault involving the secondary sensor. Either code can appear if a sensor has drifted out of its accurate range, if the sensor wiring has a loose or corroded connection, or if the sensor has simply failed after years of exposure to spa water temperature cycles.

Sensors are a straightforward like-for-like swap on most models — unplug the old one at the connector and plug in the replacement, no mains wiring involved. Browse temperature sensors for the right fit, and check cables and connectors if the issue traces back to a damaged harness rather than the sensor itself. Because the two sensors are matched as a pair on some control boards, replacing only one can sometimes trigger a new mismatch code — if that happens, replace both sensors together.

HL / OH - High Limit & Overheat Errors

HL (high limit) and OH (overheat) both relate to the spa's temperature safety system, but they're triggered slightly differently. The high-limit switch is a hard safety cutoff that trips when water temperature exceeds a fixed ceiling, regardless of the thermostat setting. OH is the pack's software-level overheat protection, which can trigger from either a genuine high-temperature condition or a sensor that's incorrectly reporting one.

Both codes share root causes with flow faults: a restricted filter or low flow means less water movement past the heater, so the water right at the element heats up faster than the bulk water, tripping the limit switch even though the spa "feels" normal temperature. Always rule out filter and flow issues first. If flow is confirmed good and the code repeats, test the sensors, then inspect the heater element for scale buildup or a failing element, and the control pack itself if sensors and heater check out. A high-limit trip from a genuinely overheated spa (for example, a stuck-on heater relay) is a control pack issue, not a DIY wiring repair — cut power at the breaker and have a licensed electrician or qualified spa technician diagnose a relay or board fault.

Er1-Er4 Generic Codes

Er-prefixed codes are generic fault codes used across several Hot Spring control board generations, and the specific number maps to the type of electrical fault rather than a specific component location:

  • Er1 — sensor open circuit (broken wire or failed sensor)
  • Er2 — sensor short circuit (pinched, corroded, or internally shorted wiring)
  • Er3 — pressure or flow switch reading closed/flow when the pump is off
  • Er4 — pressure or flow switch reading open/no-flow when the pump is on

Because these are generic fault types, the fix depends entirely on which component is tied to that circuit on your specific board. Start by checking the obvious mechanical cause (filter, water level, stuck switch) before assuming a part has failed. If the fault is consistent and repeatable, it's a sensor or switch replacement; if it appears intermittently or alongside other codes, suspect a wiring or connector issue rather than the part itself.

dEr / Protection Mode / Standby

dEr, sometimes shown as "dr" or described as Protection Mode or Standby on newer IQ 2021 panels, means the control pack has shut down active heating to protect the system after detecting a fault it couldn't resolve automatically. This is a safety state, not a standalone problem — it's almost always triggered by one of the faults above (flow, sensor, or high-limit) that wasn't cleared.

The pack will typically hold in this protected state until power is cycled. Resolve the underlying cause first — clean the filter, check water level, confirm sensors are reading correctly — then power cycle at the breaker as described below. If Protection Mode re-triggers immediately after a reset with no clear cause, that points to a control pack fault rather than a sensor or switch, and warrants a technician inspection of the control pack.

Salt System Alerts (FreshWater Salt System)

Flair models and other Hot Spring spas equipped with the FreshWater Salt System add alerts tied to water chemistry on top of the standard heating and flow codes. The system monitors salt concentration (targeting roughly 1,750 ppm) and the condition of the salt cell.

  • Low-salt warning: Appears when salt concentration drops below the target range. Add salt per the dosing instructions in your owner's manual and retest rather than guessing at quantity — overcorrecting creates its own water balance problems.
  • Code 4: Commonly reported as a low-salt condition on Flair models — confirm with a test strip or digital meter before adding salt, since a fouled sensor can occasionally report low salt inaccurately.
  • Code 5: Typically points to a salt cell or sensor fault rather than a chemistry problem — inspect the cell for scale buildup or a loose connection before assuming the cell has failed outright.

Salt system codes are specific to models with that option installed and won't appear on standard Hot Spring chlorine/bromine spas. If your spa doesn't have a FreshWater Salt System, a code in the 4-5 range is more likely a generic Er-code fault — cross-check against the table above.

Not every heating problem throws a code. A few related symptoms are worth ruling out alongside the error code table:

  • No power at all: Check the breaker first. If it has tripped, cut power, reset once, and see if it holds. A breaker that trips repeatedly points to a ground fault in the heater, pump, or wiring and needs a licensed electrician — don't keep resetting it.
  • GFCI trip: Spas run on a GFCI-protected circuit by design. A single nuisance trip (after a storm, for example) is common and not necessarily a fault. Repeated trips indicate a ground fault somewhere in the electrical system. See our GFCI collection for replacement units, but have a qualified electrician diagnose the actual fault rather than just swapping the GFCI.
  • Spa lock activated: If the display shows a locked padlock icon or won't respond to temperature adjustments, the control panel has been locked (often unintentionally) rather than faulted. Check your owner's manual for the lock/unlock button sequence specific to your panel — it varies between IQ 2020 and IQ 2021 displays.
  • Display unresponsive with no code: Points to the topside panel or its connection to the pack rather than a sensor or flow issue. See keypad overlays.

How to Reset Your Hot Spring Spa

Most codes clear on their own once the underlying cause is resolved, but a full power cycle is often needed to clear Protection Mode or a stubborn display glitch.

  1. Resolve the obvious cause first — clean or replace the filter, check water level is above the skimmer, confirm no valves are closed.
  2. Cut power to the spa at the breaker. Do not attempt to access the control pack or wiring beyond the breaker itself.
  3. Wait at least one to two minutes to allow the control board to fully discharge and reset.
  4. Restore power at the breaker and watch the display through its startup sequence.
  5. Allow the spa several minutes to re-prime circulation before judging whether the code has cleared — some packs briefly show a priming or flow message that is normal during startup.
  6. If the same code returns immediately or within a heating cycle, the underlying part — not just the software state — needs attention.

DIY Fix vs. When to Call a Technician

Most of the fixes above are reasonable DIY jobs because they involve swapping a low-voltage sensor or switch at a plug-in connector, not mains wiring:

  • DIY-friendly: filter cleaning/replacement, temperature sensor swap, flow or pressure switch replacement, clearing an air lock, resetting a locked keypad, power cycling at the breaker.
  • Call a licensed electrician or spa technician: repeated GFCI or breaker trips, any work inside the control pack enclosure, heater element replacement if it involves disconnecting mains wiring, a control pack that needs replacing, or any code that returns immediately after a correctly performed reset.

As a rule, if the fix is "unplug one connector and plug in a new part," it's within reach for most owners. If the fix requires opening the pack to access line-voltage wiring, cut power at the breaker and bring in a professional rather than guessing.

Preventive Maintenance to Avoid Error Codes

Most Hot Spring error codes trace back to one of three root causes: a dirty filter, low water level, or water chemistry drift. All three are preventable with a basic maintenance routine:

  • Rinse the filter every two to four weeks and do a deeper chemical soak on the schedule in your owner's manual — this alone prevents the majority of FL1/FLO and HL/OH codes.
  • Check water level weekly and top off before it drops below the skimmer intake.
  • Test salt concentration monthly on FreshWater Salt System models and adjust toward the 1,750 ppm target rather than waiting for a low-salt alert.
  • Inspect the sensor and switch connectors for corrosion or moisture intrusion during filter changes — catching a loose connection early avoids an intermittent fault turning into a full component failure.
  • Keep a spare filter and, if your spa is older, a spare sensor or flow switch on hand — these are the parts most likely to need replacement over the life of the spa.

FAQ

What does FL1 or FLO mean on a Hot Spring spa?

FL1 and FLO indicate the control pack is not detecting water flow through the heater. The most common causes are a dirty filter, low water level, a closed valve, or an air lock; if those check out, the flow or pressure switch itself has likely failed.

Why does my Hot Spring spa show SN1 or SN3?

SN1 and SN3 are temperature sensor fault codes. SN1 points to the primary sensor and SN3 to a mismatch involving the secondary sensor. Both usually mean a sensor has failed or its wiring connection has loosened or corroded.

How do I clear an error code on my Hot Spring spa?

Fix the underlying cause first — clean the filter, check water level, verify no valves are closed — then cut power at the breaker, wait one to two minutes, and restore power. If the code returns immediately, the part causing the fault needs to be inspected or replaced rather than just reset.

What is Protection Mode on a Hot Spring spa?

Protection Mode (sometimes shown as dEr or dr) means the control pack has shut off heating to protect the system after an unresolved fault, typically a flow, sensor, or high-limit issue. Resolve the root cause, then power cycle the spa to clear it.

Where can I find the official Hot Spring error code list for my model?

Error code wording varies by control board generation and model year. For the exact code list matching your spa's panel (IQ 2020, IQ 2021, or an older topside display), check the owner's manual for your model, available from hotspring.com.

Parts mentioned in this guide

Related guides

Not sure which part fits your spa?

Send us a photo for free Photo Identification. Our parts team typically responds in about 2 hours during business hours.

Photo Identification

Covered by our Perfect Fit Guarantee.