Spa Unions, Tailpieces & Fittings
Unions are what let a pump or heater be disconnected from the spa plumbing without cutting pipe. Because they carry water pressure and get opened and closed every time a pump, wet end or heater is serviced, the nuts, tailpieces and sealing faces wear, crack and strip. This collection covers the pump and heater union parts we list, sorted by the numbers that decide fitment: pipe size, thread type and brand.
How to match a union part
- Which side of the union is broken. A union has three pieces: the tailpiece that connects to the plumbing, the nut that draws it tight, and the threaded fitting on the pump or heater. Replace only the piece that is damaged, and make sure the new piece mates with the two you keep.
- Size. Listings include 3/4", 1-1/2", 2", 2-1/2" and 3" parts. Measure the pipe or fitting, or read the size off the old part, before ordering.
- Thread and socket code. Titles use MBT (male buttress thread), FBT (female buttress thread), MPT (male pipe thread) and S (slip, a socket that is glued to pipe). A listing such as "2" MBT x 2" S tailpiece" has a buttress thread on one end and a slip socket on the other. The codes have to match the thread on your pump or heater.
- Pump vs. heater. Heater unions, half unions and split nuts are listed separately from pump unions. They are sized for different fittings, so do not substitute one for the other without checking the size and thread.
- Brand and part number. Pump and heater makers use their own dimensions. Where you have the part number from the old piece or the equipment label, match it exactly. Our listings include Waterway, Aqua-Flo by Gecko, Balboa, HydroQuip, Magic Plastics, LX, Hydro Air, Pasco, Sundance Spas, Dreammaker Spas, Valterra and Gecko Alliance parts.
- Split nuts. A split nut opens in two pieces so it can be fitted where the plumbing is already glued up and a one-piece nut cannot be slid over the pipe.
Symptoms that point to a union part
- Water dripping or weeping at a union while the pump runs.
- A cracked or chipped union nut, or a nut that spins without tightening.
- Stripped or crossed threads on a tailpiece or fitting.
- A union that leaks again soon after being tightened. The gasket or O-ring is often the cause, not the nut, so check seals and gaskets as well.
Hand-tighten and then snug unions rather than forcing them. Over-tightening is a common way to crack a nut.
Replacing a wet end or heater
When you replace a pump wet end, Waterway pump or main pump, the port size and thread on the new unit must match your existing unions. It is a good time to inspect the nuts and tailpieces and replace any that are cracked or worn. The same applies to heater work, where the heater unions and tailpieces are opened every time the heater is removed.
For a leak that comes from the pump itself rather than the plumbing, see spa pump seal leak: signs and replacement. If the whole spa is losing water, start with why your hot tub is leaking from the bottom.
Frequently asked questions
What does MBT mean on a union or tailpiece?
MBT stands for male buttress thread, the external thread that accepts a spa union nut. FBT is the female version. Match the thread type on your pump or heater to the part you order.
What does the S in "2" S x 2" S" mean?
S stands for slip, a smooth socket that is solvent-welded to pipe. A slip end connects to the plumbing, and the other end carries the thread.
Can I use a pump union on a heater?
Do not assume so. Heater and pump unions are listed separately because the sizes and threads differ by model. Match the part number or measure and compare thread types before ordering.
Do I need to replace the whole union or only the nut?
Only the damaged piece, in most cases. If the nut is cracked, a new nut often solves it. If threads on the tailpiece or the fitting are damaged, replace that piece, and check that the sealing gasket is in good condition.
Why does my union keep leaking after I tighten it?
Look at the gasket or O-ring first, then for cracks in the nut or tailpiece and for damaged threads. Overtightening can make the problem worse.
Do I need new unions when I replace a pump?
Not always. If the new pump has the same port size and thread as the old one, your existing unions can be reused when they are in good condition. If the sizes or threads differ, order matching tailpieces and nuts with the pump.























