Do You Need to Winterize Your Hot Tub?
Not every hot tub needs a full winterization. The decision comes down to whether the tub will keep running through the cold months or sit idle.
You should fully winterize if:
- The property will be vacant for weeks or months (vacation home, cabin, rental between tenants).
- You're decommissioning the spa permanently or moving it.
- You've had repeated power outages in a cold climate and can't guarantee the heater will keep cycling.
- The equipment is old or already leaking, and you don't trust it to run unattended.
You can likely skip the drain-down and just run the tub through winter if you use it regularly, live somewhere with reliable power, and the spa's pumps, heater, and control pack are in good working order. Running a healthy hot tub through winter is usually easier on the equipment than repeated drain-and-refill cycles.
If you're unsure which camp you're in, read both paths below before deciding — the risk of skipping winterization when you shouldn't is a cracked pipe, pump housing, or heater, all of which cost far more to fix than an afternoon of draining.
What You'll Need: Winterizing Supplies & Tools
- Wet/dry shop vac (a standard household vacuum will not work and can be damaged by water)
- Non-toxic propylene glycol RV antifreeze (not automotive antifreeze)
- Garden hose
- Towels and a large sponge
- Mild, non-foaming cleaner for the shell interior
- A screwdriver or wrench for your drain valve or cap, if required
- Optional: a pre-packaged hot tub winterizing kit, which usually bundles a blow-out adapter, antifreeze, and a small shop vac attachment
If your filters, seals, or a drain valve gasket are worn, this is a good time to check our seals and gaskets and plumbing seals collections so you're not reinstalling a leak in spring.
Step 1: Turn Off Power to the Hot Tub
Cut power at the breaker dedicated to the spa before you touch any plumbing or electrical components. Do not rely on the spa's topside control to "turn off" the unit — it does not disconnect power at the panel. If you're not sure which breaker feeds the tub, label it now, before winter, so you're not guessing in the dark months later.
If anything beyond unplugging or flipping a breaker is required — for example, if you need to access wiring at the control pack or GFCI — stop and call a licensed electrician. Winterizing should never require you to open up mains wiring.
Step 2: Drain the Hot Tub Completely
Most spas have a drain valve or spigot near the base of the cabinet. Attach a garden hose, direct it to a location where the water can run off safely, and open the valve. If your tub doesn't have a gravity drain or the valve is slow, a small submersible pump will speed things up considerably.
Let the tub drain fully before moving to the next step. Partial draining is one of the most common reasons winterizing fails — water left in the footwell or low plumbing loops is exactly what freezes and cracks a pipe.
Step 3: Remove and Clean the Filters
Pull the filter cartridges and rinse off loose debris. Winter is a good time to do a deeper soak-clean, or to replace filters that are past their useful life — a filter that's compressed, torn, or chronically clogged won't filter well even after cleaning. Store filters indoors, dry, away from freezing temperatures; a garage shelf or basement works fine.
Leave the filter compartment open or loosely capped (not sealed) for the winter so air can circulate and any residual moisture can evaporate instead of sitting and growing mildew.
Step 4: Blow Out the Plumbing Lines and Jets
This is the step most guides skim over, and it's the one that actually prevents freeze damage. Even after draining, water sits in the plumbing loops behind each jet, in the pump housings, and in the heater tube. Use a wet/dry shop vac set to blow (not suction) and hold it firmly over each jet face, one at a time, for several seconds until you see air bubbling instead of water spraying.
Work systematically around the spa — every jet, every water feature, the spillway if there is one — so you don't miss a line. Pay particular attention to the lowest jets and any line that runs below the equipment pack, since those hold water the longest.
If your spa has two pumps, you'll need to blow out each pump's circuit separately, since they often don't share plumbing loops. Check the main pumps and circulation pumps collections if you're unsure how many pumps your model uses, or if you discover a pump that's cracked or weeping during this process.
Step 5: Add Non-Toxic RV Antifreeze to Pipes
Once the lines are blown out, pour a small amount of non-toxic propylene glycol RV antifreeze into each jet line, the pump wet ends, and any drain line you can access directly. This type of antifreeze is safe to flush out in spring because it's non-toxic and biodegradable — automotive antifreeze is toxic and should never go anywhere near a hot tub.
You don't need to fill the lines, just enough antifreeze to coat the interior of the pipe and displace any remaining moisture film. A cup or two per line is typical for most residential spas, though exact amounts depend on your plumbing run length. If a wet end is worn or cracking, consider swapping it now from our pump wet ends collection rather than waiting for a spring failure.
Step 6: Dry Out the Shell, Pumps, and Equipment Compartment
Use a sponge or shop vac to soak up any remaining standing water in the footwell and the lowest point of the shell — this is where water pools regardless of how well the drain worked. Wipe down the shell interior with a mild, non-foaming cleaner to remove any residue and reduce the chance of mold or mildew developing over the winter months.
In the equipment compartment, towel-dry the pump housings, heater, and control pack area. Leave an access panel slightly cracked rather than fully sealed, so trapped moisture has somewhere to go. A fully sealed, damp compartment over a cold winter is a reliable way to encourage corrosion on terminals and connectors — if you spot any corrosion already, it's worth inspecting your control pack, cables and connectors, and GFCI before you close everything up.
Step 7: Cover and Secure the Hot Tub
Put the cover back on and make sure it seats evenly without gaps — a cover that's sagging, waterlogged, or torn won't keep snow and moisture out, which defeats the purpose of everything you just did. Use the cover's locking straps or a cable lock to keep it secured against wind.
In especially cold or snowy climates, a thermal cover cap or an additional tarp over the cover adds a layer of insulation and keeps snow load off the cover itself. Clear heavy snow accumulation periodically rather than letting it sit for weeks.
Alternative: Keeping Your Hot Tub Running All Winter
If you use your spa through the winter, or simply don't want to deal with a spring refill, the better option is often to leave it running and let the equipment protect itself. Most modern control packs include a freeze-protection mode that automatically cycles the pumps and heater when sensor temperatures drop near freezing, even if the spa isn't in use. This keeps water moving through the lines so it can't sit still long enough to freeze.
For this to work reliably, you need:
- Stable power — a tub in freeze-protection mode does nothing during an extended outage.
- A functioning temperature sensor and control pack — if your spa isn't cycling on its own during cold snaps, check your sensors and control pack, since a failed sensor is a common reason freeze protection doesn't trigger.
- A heater that's actually heating — a weak or failing heater element can keep the water above the sensor's freeze threshold but still too cold to prevent ice forming in an exposed line.
- A cover in good condition, since it's your main defense against heat loss overnight.
Do not leave a spa running unattended through winter if you already know the pump, heater, or control pack is failing — freeze protection only works if the parts it depends on are healthy. In that case it's safer to winterize fully, repair the faulty part, and refill once you're confident the system will hold.
How to Re-Open Your Hot Tub in Spring
Reversing a winterization is straightforward:
- Remove the cover and inspect the shell, jets, and equipment compartment for any cracks, stains, or signs a line froze despite your prep.
- Close the drain valve and flush each jet line with a garden hose to clear out the antifreeze before refilling.
- Reinstall clean (or new) filters.
- Fill the spa, restore power at the breaker, and prime the pumps per your owner's manual before running the heater.
- Test the water chemistry once it's up to temperature, and run through a full jet cycle to confirm every pump and line is clear.
If a pump won't prime, the heater won't fire, or the control pack throws an error on startup, that's usually a sign something froze or a seal failed over winter — check pressure switches, heaters, and seals and gaskets as common culprits before assuming the worst.
Cost of Professional Winterizing vs. DIY
| Option | Typical Cost | What's Included |
|---|---|---|
| DIY | $0–$20 | Antifreeze, your own time and a shop vac you may already own |
| Hiring a pro | $100–$300 | Labor, draining, blow-out, antifreeze, and often a basic equipment inspection |
Searching "winterize hot tub near me" will turn up local spa service companies and some pool companies that offer seasonal winterizing as an add-on. It's worth the cost if you're not comfortable with the blow-out step, you're leaving the property for an extended period, or your spa has a complex plumbing layout with multiple pumps and water features. For a straightforward single-pump residential spa, DIY winterizing is well within reach for most owners in an afternoon.
Common Winterizing Mistakes to Avoid
- Skipping the blow-out step. Draining alone leaves water trapped in jet lines and pump housings — this is the single biggest cause of winter cracks.
- Using automotive antifreeze. It's toxic and not designed for this use; always use non-toxic propylene glycol RV antifreeze.
- Forgetting low points. The footwell and the lowest plumbing loops hold water longest and freeze first.
- Sealing the equipment compartment completely. Trapped moisture with no airflow leads to mold and corroded connectors over a long winter.
- Leaving a damaged cover in place. A torn or waterlogged cover won't protect the shell from snow and moisture, undoing the rest of the work.
- Assuming freeze protection works on a failing control pack. If the sensor or heater isn't functioning, the "keep it running" approach won't actually prevent a freeze.